flyhigher87 Posted September 15, 2017 Share Posted September 15, 2017 Hey guys hope all is well. So I'm in the middle of a vodka run and my distillate is pulsing. By this I mean, the distillate will completely stop for like 10-15 seconds and then all of a sudden open the flood gates for like 5 seconds. This has only happened once before on a previous run. Normally my still is pretty steady stream a little variation in flow rate but nothing this drastic. My still is a small 50 gallon it has four plates and a large random packed section with copper scrubbers and raschig rings. I am running a dephlag with little trickle of water through it to maintain 95% abv. So Why is my distillate flow rate so crazy today?? thank you. Link to comment Share on other sites More sharing options...
Classick Posted September 15, 2017 Share Posted September 15, 2017 Sounds like a back pressure issue. Did this just start ot has it always done that? Does it only do it when you're running at 95%if you lower it to 90 do you still get the pulsation? Might be useful to share a pic of the still. Link to comment Share on other sites More sharing options...
PeteB Posted September 18, 2017 Share Posted September 18, 2017 Is the spirit outlet open to the air or submerged as in a parrot? If open then it is possible for cold air to get sucked into the condenser if the still slows for a moment. If the condenser is short the cold air gets into the still and cools the vapor in there causing a slight negative pressure which sucks more cold air in. Then as that air heats up it rushes out again, when the air has finished expanding the output stops for a moment and more cold air gets drawn in. Huffing. If that is what is happening then a submerged outlet will stop it. Link to comment Share on other sites More sharing options...
FaintingGoatSpirits Posted September 18, 2017 Share Posted September 18, 2017 That happened to me one time. I was running my steam pressure too high and it over powered my Dephleg Link to comment Share on other sites More sharing options...
Silk City Distillers Posted September 18, 2017 Share Posted September 18, 2017 Very cold condenser feed water amplifies the situation that @PeteB mentioned. Link to comment Share on other sites More sharing options...
Foreshot Posted September 18, 2017 Share Posted September 18, 2017 Google "Parrot Surge Breaker". Most of the vendors here offer them. It will reduce/eliminate the backpressure/surge cycle. Link to comment Share on other sites More sharing options...
flyhigher87 Posted September 19, 2017 Author Share Posted September 19, 2017 So I have a parrot but before the parrot it has holes on the side below the condenser, so it is essentially open to the air. And @Silk City Distillers You may be spot on about the cold condenser water, I converted an old Air conditioner into our water chiller and the water will get down to almost 0 C, I'm going to install a temp probe and controller soon, but I'll be sure to watch the condenser water temperature. Thanks for the replies guys Link to comment Share on other sites More sharing options...
flyhigher87 Posted October 27, 2017 Author Share Posted October 27, 2017 So I’m not sure anyone is following this or cares. But if you are and you do I fixed the problem. I was reading a home distillers forum and saw someone talking about boiling chips. So I threw in some ceramic rings and problem solved. So I guess the gas had no nucleation point and the liquid was super heating and then flash boiling. So this worked but I never in a million years would have thought that a still with an agitator would have needed boiling chips. Anyone else need them in a commercial still? 1 Link to comment Share on other sites More sharing options...
whiskeytango Posted October 27, 2017 Share Posted October 27, 2017 I get this a little bit when I’m running to much heat to the kettle and also real cold water to the condenser. who made your still. Do they have any recommended fixes? Link to comment Share on other sites More sharing options...
Classick Posted October 27, 2017 Share Posted October 27, 2017 Thats great news. congrats on diagnosing the problem Link to comment Share on other sites More sharing options...
Foreshot Posted October 27, 2017 Share Posted October 27, 2017 Good catch! I would not have thought of that. Link to comment Share on other sites More sharing options...
whiskeytango Posted October 27, 2017 Share Posted October 27, 2017 Sorry i posted my last comment before i saw your response. Boiling chips.. Hm i agree never would have thought about needing them. Are you thinking that it was boiling then stoping then boiling then stoping? Causing the pulsing? Link to comment Share on other sites More sharing options...
flyhigher87 Posted November 29, 2017 Author Share Posted November 29, 2017 @whiskeytango absolutely. Now that I have the "boiling chips" in the still it still pulses a little but not as bad. And I can actually here the rings rattling in the still(boiling) and then go dead silent(not boiling). Link to comment Share on other sites More sharing options...
Blackheart Posted November 29, 2017 Share Posted November 29, 2017 If you use a standard parrot, make sure it's vented. This stops it immediately. 1 Link to comment Share on other sites More sharing options...
PeteB Posted December 1, 2017 Share Posted December 1, 2017 I have been thinking about the physics of why a still would pulse. Interest for physics nerds only. The boiling chips comment gave me an idea, the boiling appears to stop and start. A plausible explanation is when the pot boiling vigorously there is a very slight increase in pressure in the still because the rapidly evolving vapour This slight pressure increase will increase the boiling point of the still contents and boiling stops, (but temperature now increases because no heat lost as Latent) Now not boiling or producing vapour and pressure drops, boiling point drops and the contents will start boiling again, even more vigorously because the liquid is now slightly superheated. Pressure builds again and boiling stops........................etc..... Someone mentioned very cold condenser water could cause pulsing. The above theory still applies, the really cold water creates a slight negative pressure allowing rapid boiling then pressure builds .... etc...... 1 Link to comment Share on other sites More sharing options...
meerkat Posted December 1, 2017 Share Posted December 1, 2017 From one physics nerd to another.... I believe you are on the right track with your interpretation that it is the boiling that stops and starts. I have seen a similar phenomenon in continuous columns that have significantly oversized external reboilers. These get into a similar cycle of pulsing and the accepted interpretation was always that boiling was stopping and starting. With the very oversized reboiler, heat can be passed through the tubes into the liquid so fast that a vapor blanket is formed on the inside of the tubes. The heat transfer through vapor is much slower than through liquid and suddenly the heat transfer stops. The bouyancy of the vapor gradually causes the vapor to rise out of the reboiler and colder liquid flows in from the bottom of the column. Heat transfer picks up because of the higher thermal conductivity of the liquid and the cycle repeats. Link to comment Share on other sites More sharing options...
Hudson bay distillers Posted December 1, 2017 Share Posted December 1, 2017 makes sense pete and meerkat , so with this in mind what would you guys say the optimum temp for the preheated feed to be when entering a continuous column , not factoring in the pressure change from the feed line to atmospheric in the column . tim Link to comment Share on other sites More sharing options...
captnKB Posted December 1, 2017 Share Posted December 1, 2017 On the last continuous I ran we fed bourbon mash beer to the column at 130F. The purpose of heating the feed is mainly to ensure all alcohol is flashed out before the mash reaches the base of the column Link to comment Share on other sites More sharing options...
meerkat Posted December 3, 2017 Share Posted December 3, 2017 @Hudson bay distillers If there is such a thing as a universal optimum temperature for the feed to a continuous column then I would say it is the boiling point corresponding to the composition of the feed. If it is colder than this it causes internal reflux in the bottom part of the column which does not do much towards providing a high strength top product. On the other hand if it is hotter than the boiling point you will find that you need to provide a higher reflux ratio from the condenser which increases the water requirements on the condenser but saves a bit of heat on the boiler. But I have seen feed temperatures from substantially below the boiling point all the way through to feeding the column with 100% vapour. If the feed is not a liquid at its boiling point then a change in diameter of the column at the feed point may be required. Link to comment Share on other sites More sharing options...
Hudson bay distillers Posted December 3, 2017 Share Posted December 3, 2017 thanks captn and meerkat that confirms what i was thinking . i would think that a feed temp and pressure change that would flash off the alcohol vapors but keep heavier components at a liquid would be optimal temp . ...sorryfor getting off topic tim Link to comment Share on other sites More sharing options...
Silk City Distillers Posted December 3, 2017 Share Posted December 3, 2017 From some of the design threads around the interwebs, running the feed on the bleeding edge of boiling is problematic as you risk boiling in the feed lines from the last heat exchanger to the input, causing all sorts of sputtering and inconsistent feed rates. Link to comment Share on other sites More sharing options...
Hudson bay distillers Posted December 3, 2017 Share Posted December 3, 2017 true but upping the pressure in the feed line drops the boiling point keeping it at a stable nonboiling point while its in the feed line , dropping it back to atmospheric pressure when released into the column drops the boiling point causing it to boil and vaporise instantly without taxing any energy from the column . tim Link to comment Share on other sites More sharing options...
kelbor Posted December 5, 2017 Share Posted December 5, 2017 I'm currently wrastling with this same issue as the O.P.. 50 gallon pot, steam heated, 6" diameter column still has a three foot packed section below six bubble plates. It will chug along all happy (but very slowly - about 1.25 gallons an hour) for about 5 hours or so and them out of no where start a massive surge cycle. Parrot has surge breaker holes, I also read about the flash boiling a while ago so I cut up several sections of copper pipe and put them in the pot. Didn't help. I have been somewhat successful by turning down the dephlag and running real low heat with the thinking that my surging was coming from too much condensate return 'chocking' the packed section and creating a sort of liquid blockage for the rising vapors. My packed section is pretty fine copper mesh (used to keep mice and rats from chewing through holes). No sure if this is the issue or not but this is driving me fairly crazy as every time it surges I have to crank up my dephlag, turn down my heat, and re-equalize my column. Any thoughts? Link to comment Share on other sites More sharing options...
adamOVD Posted December 30, 2017 Share Posted December 30, 2017 On 10/27/2017 at 11:14 AM, flyhigher87 said: So I threw in some ceramic rings and problem solved. Could you elaborate on ceramic rings. I'd like to try the same thing, but don't want to have to fish them out whenever I cook mash in my boiler, and also a little worried about the agitator hitting them. Thinking of just cutting some short sections of copper pipe, drilling some tiny holes in them, and dropping them over the shaft of the agitator. Anyone see anything wrong with that? Link to comment Share on other sites More sharing options...
adamOVD Posted January 1, 2018 Share Posted January 1, 2018 Also recently had a terrible surging problems on a run for reasons I won't go into detail because it probably won't really apply to anyone else, rigging this up with what I had on hand, before the parrot allowed me to at least get through the run. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now